Horizontal lifter, for stainless steel plates and constructions type STS-A RX-lift
• EN 13155
• usage: lift and transport stainless steel plates and structures in a horizontal position
• for safe transport, the gripper surface must be dry, clean and
non-greasy, free of any lubricant or dust
• Do not use on smooth, polished surfaces as they have various
lubricating compounds on them
• must clean the jaw of the gripper regularly in clean water, do not use solvents
• must check the handle before each use, make sure that it is
clean and undamaged, otherwise remove it from use
Horizontal plate clamp type HPC RX-lift
• EN 13155
• horizontal lifting and transport of sheets and steel plates
• use in pairs, multiple pairs or in "tripod" configuration in combination with 2-leg or 3-leg slings and suitable shackles
• for material with max. surface hardness 30 HRC
• temperature of use from -40 to 100°C
• lateral angle during lifting must not exceed angle of 15°
• rate capacity is calculated on basis of the top angle of 0-30° (for angels 30-60° between clamp and sling, clam capacity is decreased)
Horizontal plate clamp type JPD (LC) RX-lift
• EN 13155
• horizontal lifting and transport of thin steel plates, beam profiles and bending sheets
• reverse jaw enables transport of the sheets that tend to bend during lifting or manipulation of beam profiles (gripping on the side of the beam or profile flipping)
• use in pairs, multiple pairs or in "tripod" configuration in combination with 2-leg or 3-leg slings and suitable shackles
• it is prohibited to use in combination with 4-leg sling (when lifting long plates, use spreader beam with combination with 1-leg or 2-leg slings)
• for material with max. surface hardness 30 HRC
• temperature of use from -40 to 100°C
• lateral angle during lifting must not exceed angle of 15°
• rate capacity is calculated on basis of the top angle of 0-30° (for angels 30-60° between clamp and sling, clam capacity is decreased)
Horizontal plate clamp type PPD RX-lift
• EN 13155
• horizontal lifting and transport of sheets and steel plates and constructions
• the clamp contains a safety lock mechanism that ensures that the load does not slip when is being lowered
• it is prohibited to use in combination with 2-leg, 3-leg or 4-leg sling (when lifting it is mandatory to use spreader beam with combination with 1-leg slings)
• for material with max. surface hardness 30 HRC
• temperature of use from -40 to 100°C
• lateral angle during lifting must not exceed angle of 15°
• rate capacity is calculated on basis of the top angle of 0-30° (for angels 30-60° between clamp and sling, clam capacity is decreased)
Horizontal plate clamp type THK RX-lift
• EN 13155
• horizontal lifting and transport of sheets and steel plates
• use in pairs, multiple pairs or in "tripod" configuration in combination with 2-leg or 3-leg slings and suitable shackles
• it is prohibited to use in combination with 4-leg sling (when lifting long plates, use spreader beam with combination with 1-leg or 2-leg slings)
• for material with max. surface hardness 30 HRC
• temperature of use from -40 to 100°C
• lateral angle during lifting must not exceed angle of 15°
• rate capacity is calculated on basis of the top angle of 0-30° (for angels 30-60° between clamp and sling, clam capacity is decreased)
Horizontal steel and concrete pipe clamp type TPH RX-lift
Hvataljka za čelične cijevi tip YG RX-lift
Magnetic hand lifter MAG50
• EN 13155
• lifting and transport of the ferromagnetic materials like plates and blocks up to 50 kg
• temperature of use from -10 °C to 60 °C
• safety factor: 3:1
• the lifting capacity depends on the thickness and chemical composition
of the material and roughness of the surface to which the lifter is attached
• can only be used for handling material manually (lifting of load fixed to a magnetic hand lifter with another lifting equipment is forbidden)
Select options
This product has multiple variants. The options may be chosen on the product page
Permanent magnetic lifter PML RX-lift
• lifting and transport of the ferromagnetic materials like plates,
blocks and round profiles
• temperature of use from -40 °C to 80 °C
• safety factor: 3,5:1
• the lifting capacity depends on the thickness and chemical composition
of the material and roughness of the surface to which the lifter is
attached
Select options
This product has multiple variants. The options may be chosen on the product page
Universal plate clamp type IPU10 Crosby
• EN 13155
• vertical lifting and transport of the steel plates and construction
• full 180° turning range for material transfer, turning or moving
• safety lock mechanism
• min. capacity is 10% max. capacity
• for materials with a a surface hardness up to 37 HRC (450 HB)
• jaw opening from 0 to 80 mm
• temperature of use form -40 to 100°C
• 10 year of warranty
• manufacturers web page: https://www.thecrosbygroup.com/products/lifting-clamps/vertical/standard/crosby-ipu10-vertical-lifting-clamps/?language=en
Universal plate clamp type PCD RX-lift
• EN 13155
• vertical lifting and transport of the steel plates and construction
• full 180° turning range for material transfer, turning or moving
• safety lock mechanism
• min. capacity is 10% max. capacity
• for materials with a a surface hardness up to 30 HRC (285 HB)
• not suitable for lifting stainless steel and copper
• jaw opening from 0 to 80 mm
• temperature of use form -40 to 100°C